P2280 Air Flow Restriction/Air Leak Between Air Filter and MAF
OBD-II Trouble Code Technical Description
Air Flow Restriction/Air Leak Between Air Filter and MAF
What does that mean?
This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). Although generic, the specific repair steps may vary depending on make/model. That may include but is not limited to vehicles from Dodge, Ram, Audi, Chevrolet, Ford, GMC, Jeep, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
If your vehicle has stored a code P2280, it means that the powertrain control module (PCM) has detected insufficient airflow between the air filter element and the mass airflow (MAF) sensor.
In order for today���s engines to perform at peak efficiency, air and fuel must be regulated precisely. The fuel pump and fuel injectors provide fuel in adequate supply and the throttle body (or throttle bodies) allows metered air to enter the intake. The delicate air/fuel ratio must be carefully monitored and adjusted; constantly. This is accomplished using the PCM with inputs from engine sensors such as the MAF, the manifold air pressure (MAP) sensor, and the heated oxygen sensors (HO2S).
If the PCM detects that there is insufficient ambient air being drawn into the MAF sensor, while the engine is running, a code P2280 may be stored and a malfunction indicator lamp (MIL) illuminated. Multiple drive cycles with a failure may be required for MIL illumination.
A typical MAF sensor:
What is the severity of this DTC?
A stored code P2280 will likely be accompanied by severe drivability symptoms. The conditions which contributed to code storage should be rectified as quickly as possible.
What are some of the symptoms of the code?
Symptoms of a P2280 trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P2280 troubleshooting steps?
In order to diagnose a code P2280, a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information will be required.
If you can use your source of vehicle information to locate a technical service bulletin (TSB) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited, it could yield helpful diagnostic information.
Begin with an inspection of the air filter element. If it is excessively dirty or clogged, replace the filter and test-drive the vehicle to see if the symptoms subside. If not, carefully check the air inlet pipe for kinks, cracks, or signs of collapse. If abnormalities are found, the air inlet pipe should be replaced with an OEM replacement part.
If MAF codes accompany the P2280, inspect the MAF Sensor hot wire for unwanted debris. If debris is present on the hot wire, follow manufacturer���s recommendations for cleaning the MAF sensor. Never use chemicals or cleaning methods which are not specifically recommended by the automaker.
If the air filter is clean and the air inlet pipe is in good working order, use the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. It is a good idea to write this information down before clearing the codes then test-drive the vehicle until the PCM either enters readiness mode or the code is reset.
If the PCM enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.
However, if the code is immediately reset, completing the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.
Follow manufacturer���s specifications to test the MAF and MAP sensors using the DVOM. If both these sensors are functional, test system circuits. I like to use the voltage drop method.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2280 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p2280 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p2280 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2280.
