P2264 Water in Fuel Sensor Circuit
OBD-II Trouble Code Technical Description
Water in Fuel Sensor Circuit
What does that mean?
This is a generic diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Land Rover (Range Rover), Ford, Hyundai, Jeep, Mahindra, Vauxhall, Dodge, Ram, Mercedes, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
The OBD-II trouble code P2264 is associated with the water in fuel sensor circuit, also known as the fuel composition circuit. When the Power Control Module (PCM) detects improper signals within the water in fuel sensor circuit, code P2264 will be set and the check engine light will be illuminated. The water in fuel light may also be illuminated if the vehicle incorporates this warning indicator. Refer to a vehicle specific resource to find the sensor location for your particular year / make / model configuration.
The purpose of the water in fuel sensor is to monitor the fuel which passes through it to ensure that ethanol, water, and other contaminants do not exceed a certain percentage. Additionally, fuel temperature is measured by the water in fuel sensor and converted into a voltage pulse width monitored by the PCM. The PCM utilizes these readings to adjust the engine timing for optimum performance and fuel economy.
A typical water in fuel sensor:
What is the severity of this DTC?
The severity of this code can vary tremendously from just an illuminated check engine light or water in fuel light on a vehicle that starts and runs to an automobile that will stall, misfire or not start at all. Damage to fuel system and internal engine components may occur if this situation is not corrected in a timely manner.
What are some of the symptoms of the code?
Symptoms of a P2264 trouble code may include:
What are some of the common causes of the code?
Causes for this P2264 code may include:
What are some P2264 troubleshooting steps?
The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB’s) for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the right direction.
The second step is to check the vehicle records to see when the fuel filter was replaced and visually inspect the condition of the filter. The most common causes for this code is a defective fuel filter or contaminated fuel. A visual inspection of the fuel can be conducted using a glass jar. Once a sample is taken and allowed to settle the water and fuel will separate in a matter of minutes. The presence of water in the fuel is an indication of contaminated fuel, a defective fuel filter or both. Then you should locate all of the components within the water in fuel circuit and perform a thorough visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots. Next is to check the connectors for security, corrosion and damaged pins. The sensor is normally mounted on the top of the fuel tank on most vehicles.
Advanced Steps
The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. The ideal tool to use in this situation is an oscilloscope, if available. The O-scope will provide an accurate illustration of the signal pulses and the frequency levels that will be proportional to the fuel contamination level. The typical range of frequency is from 50 to 150 hertz; with 50 hertz representing clean fuel and 150 Hertz representing a high level of contamination. Voltage requirements and signal pulses will vary based on the specific year and model of the vehicle.
Voltage Checks
The water in fuel sensor is typically supplied with a voltage reference of approximately 5-volts from the PCM. If this process identifies the absence of a power source or ground, continuity testing may be required to check the integrity of the wiring, connectors and other components. Continuity tests should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.
What are some common repairs for this code?
Common mistakes may include:
Replacing the PCM or water in fuel sensor when damaged wiring or contaminated fuel is the cause of the problem.
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your water in fuel circuit fault code. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2264 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p2264 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p2264 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2264.
