P063D Generator Voltage Sense Circuit High
OBD-II Trouble Code Technical Description
Generator Voltage Sense Circuit High
What does that mean?
This is a generic diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Jeep, Chrysler, Dodge, Ram, Cummins, Land Rover, Mazda, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
The P063D OBDII trouble code is associated with the generator voltage sense circuit. When the Powertrain Control Module (PCM) detects improper signals within the generator voltage sense circuit code P063D will be set. Based on the vehicle and the specific malfunction the battery warning light, check engine light or both will be illuminated. Related codes associated with this circuit are P063A, P063B , P063C, and P063D.
The purpose of the generator voltage sense circuit is to monitor the alternator and battery voltage during vehicle operation. The output voltage of alternator must be at a level that is capable of compensating for battery draws from electrical components including the starter, lighting and various other accessories. In addition, the voltage regulator must adjust the output to provide sufficient voltage to charge the battery.
Code P063D is set by the PCM when it detects a high electrical condition in the generator (alternator) sense circuit.
Example of an alternator (generator):
What is the severity of this DTC?
The severity of this code can vary tremendously from just an illuminated check engine light or battery warning light on a vehicle that starts and runs to an automobile that will not start at all.
What are some of the symptoms of the code?
Symptoms of a P063D trouble code may include:
What are some of the common causes of the code?
Causes for this P063D code may include:
What are some P063D troubleshooting steps?
The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB’s) for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the right direction.
The second step is a thorough visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots. Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring connectors and connections to the battery, alternator, PCM, and the voltage regulator. Some charging system configurations may be more complex including relays, fuse-able links and fuses in some circumstances. The visual inspection should also include the condition of the serpentine belt and the belt tensioner. The belt should be tight with a sight amount of flexibility and the tensioner must move freely and apply the appropriate amount of pressure on the serpentine belt. Based on the vehicle and the charging system configuration a defective or damaged voltage regulator will require an alternator replacement in most circumstances.
Advanced Steps
The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. The ideal tool to use in this situation is a charging system diagnostic device, if available. Voltage requirements will very based on the specific year and model of the vehicle.
Voltage Checks
The battery voltage should be appropriately 12 volts and the alternator output must be higher to compensate for electrical draws and charge the battery as well. The lack of voltage indicates a faulty alternator, voltage regulator or a wiring issue. If the alternator voltage output is in the appropriate range, this is an indication that the battery requires replacement or a wiring issue exists.
If this process identifies the absence of a power source or ground, continuity testing may be required to check the integrity of the wiring, alternator, voltage regulator and other components. Continuity tests should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.
What are some common repairs for this code?
Common mistakes may include:
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your generator voltage sense circuit fault code. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p063d and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p063d in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p063d and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p063d.
