P0623 Generator Lamp Control Circuit
OBD-II Trouble Code Technical Description
Generator Lamp Control Circuit
What does that mean?
This is a generic diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Ford, Lincoln, Chevrolet, GMC, Dodge, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
A stored code P0623 means that the powertrain control module (PCM) has detected a malfunction with the generator lamp control circuit.
The generator lamp is contained in the instrument panel. Its primary purpose is to warn the driver of potential charging system problems, when it is illuminated.
The PCM typically monitors the continuity of the generator lamp control circuit whenever the engine is running. The generator lamp control circuit is integral to generator operation and maintaining battery charge levels.
Each time the ignition is turned on and the PCM is energized, multiple controller self-tests are performed. In addition to running internal controller self-tests, the controller area network (CAN) is used to compare signals from each individual module to ensure that the various controllers are interfacing properly.
If a problem is detected in monitoring the generator lamp control circuit, a code P0623 will be stored and a malfunction indicator lamp (MIL) may be illuminated,. Depending upon the perceived severity of the malfunction, multiple failure cycles may be necessary for MIL illumination.
Internal control module codes must always be taken seriously. A stored code P0623 could result in a variety of drivability concerns, including a no-start and/or dead battery condition.
A typical alternator:
What are some of the symptoms of the code?
Symptoms of a P0623 trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P0623 troubleshooting steps?
A diagnostic scanner, a battery/alternator tester, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information will be required to diagnose a code P0623.
Consult your vehicle information source for technical service bulletins (TSB) that replicate the code stored, vehicle (year, make, model, and engine), and symptoms exhibited. If you find the appropriate TSB, it may yield helpful diagnostic.
Begin by connecting the scanner to the vehicle diagnostic port and retrieving all stored codes and freeze frame data. You will want to write this information down, just in case the code proves to be an intermittent one. After recording all pertinent information, clear the codes and test drive the vehicle until the code is reset or the PCM enters readiness mode. If the PCM enters readiness mode, the code is intermittent and will be more difficult to diagnose. The condition, which caused the P0623 to be stored, may even need to worsen before a diagnosis can be made. If the code is reset, continue with your diagnosis.
Use the battery/alternator tester to test the battery and make sure that it is sufficiently charged. If it is not, charge the battery as recommended and test the alternator/generator. Follow manufacturers recommended specifications for minimum and maximum voltage output requirements for the battery and alternator. If the alternator/generator is not charging, proceed to the next step in your diagnosis.
Use your source of vehicle information to obtain connector face views, connector pin-out charts, component locators, wiring diagrams, and diagnostic flow charts related to the code and vehicle in question.
Check to see if there is battery voltage on the alternator/generator warning lamp circuit by using the appropriate wiring diagram and your DVOM. If not check system fuses and relays and replace defective parts as required. If voltage is discovered at the generator warning lamp, suspect a defective alternator/generator warning lamp bulb.
If the alternator is charging, the alternator/generator warning lamp bulb is functioning properly, and the P0623 continues to reset, use the DVOM to test controller power supply fuses and relays. Replace blown fuses as required. Fuses should be tested with the circuit loaded.
If all fuses and relays appear to be functioning as intended, a visual inspection of controller related wiring and harnesses is in order. You will also want to check chassis and engine ground junctions. Use your vehicle information source to obtain ground locations for related circuits. Use the DVOM to test ground integrity.
Visually inspect system controllers for signs of water, heat, or collision damage. Any controller that is damaged, especially by water, should be considered defective.
If controller power and ground circuits are intact, suspect a defective controller or a controller programming error. Controller replacement will require reprogramming. In some cases, you may purchase reprogrammed controllers through aftermarket sources. Other vehicles/controllers will require on-board reprogramming that may only be done through a dealership or other qualified source.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0623 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0623 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0623 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0623.
