P061C Internal Control Module Engine RPM Performance
OBD-II Trouble Code Technical Description
Internal Control Module Engine RPM Performance
What does that mean?
This generic powertrain diagnostic trouble code (DTC) typically applies to many OBD-II vehicles. That may include but is not limited to vehicles from Dodge, Ram (Cummins), Ford, Chrysler, etc.
When a code P061C is stored, it means that the powertrain control module (PCM) has detected an internal performance error in the engine RPM (revolutions per minute) monitoring system. Other controllers may also detect an internal PCM performance error (with the engine RPM monitoring system) and contribute to a P061C being stored.
Internal control module monitoring processors are responsible for various controller self-test duties and overall internal control module accountability. Engine RPM calculation system input and output signals are subject to self-test and are monitored constantly by the PCM and other related controllers. The transmission control module (TCM), traction control module (TCSM), and other controllers are subject to interaction with the engine RPM monitoring system.
Engine RPM is monitored (by the PCM and other controllers) using input signals from the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor/s. Desired engine RPM is programmed into the PCM and other controllers. Actual RPM is calculated using input data from the CKP and CMP sensors, as well as the throttle position sensor (TPS), and other engine and transmission sensors. Desired RPM is then compared with actual RPM.
Whenever the ignition is on and the PCM is energized, internal engine RPM monitoring self-tests are initiated. In addition to running internal controller self-tests, the controller area network (CAN) also compares signals from each individual module to ensure that all controllers are functioning properly. These tests are performed simultaneously.
If the PCM detects an internal error in desired engine RPM and actual RPM (which exceeds the maximum allowable threshold), a code P061C will be stored and a malfunction indicator lamp (MIL) may be illuminated. Multiple ignition cycles (with a failure) may be required for MIL illumination.
Photo of a PCM with the cover removed:
What is the severity of this DTC?
Internal control module processor codes should be categorized as severe. A stored code P061C could result in serious drivability and fuel efficiency issues, suddenly and without warning.
What are some of the symptoms of the code?
Symptoms of a P061C trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P061C troubleshooting steps?
Even to the most experienced and well-equipped professional technician, diagnosing a code P061C can prove to be quite a challenge. There is also the issue of reprogramming. Without the necessary reprogramming equipment, it will be impossible to replace a defective controller and complete a successful repair.
If there are ECM/PCM power supply codes present, they will obviously need to be rectified before attempting to diagnose a P061C. Also, if there are CKP/CMP sensor or throttle position sensor (TPS) codes present, these must be diagnosed and repaired first.
Follow manufacturer’s recommendations for testing CKP, CMP, and TPS sensors. The oscilloscope can be particularly helpful when testing electromagnetic sensors. Replace failed components as required.
There are several preliminary tests that can be performed prior to declaring an individual controller defective. A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information will be required. An oscilloscope may also prove to be helpful.
Connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. You will want to write this information down, just in case the code proves to be an intermittent one. After recording all pertinent information, clear the codes and test drive the vehicle until the code is reset or the PCM enters readiness mode. If the PCM enters readiness mode, the code is intermittent and will be more difficult to diagnose. The condition, which caused the P061C to be stored, may even need to worsen before a diagnosis can be made. If the code is reset, continue with this short list of preliminary tests.
When attempting to diagnose a P061C, information may be your greatest tool. Search you vehicle information source for technical service bulletins (TSB) that parallel the code stored, vehicle (year, make, model, and engine), and symptoms exhibited. If you find the right TSB, it may yield diagnostic information that will aid you in a major way.
Use your source of vehicle information to obtain connector face views, connector pin-out charts, component locators, wiring diagrams, and diagnostic flow charts related to the code and vehicle in question.
Use the DVOM to test controller power supply fuses and relays. Test and replace blown fuses as required. Fuses should be tested with the circuit loaded.
If all fuses and relays appear to be functioning as intended, a visual inspection of controller related wiring and harnesses is in order. You will also want to check chassis and engine ground junctions. Use your vehicle information source to obtain ground locations for related circuits. Use the DVOM to test ground integrity.
Visually inspect system controllers for signs of water, heat, or collision damage. Any controller that is damaged, especially by water, should be considered defective.
If controller power and ground circuits are intact, suspect a defective controller or a controller programming error. Controller replacement will require reprogramming. In some cases, you may purchase reprogrammed controllers through aftermarket sources. Other vehicles/controllers will require on-board reprogramming that may only be done through a dealership or other qualified source.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p061c and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p061c in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p061c and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p061c.
