P025D Fuel Pump Module Control Circuit High
OBD-II Trouble Code Technical Description
Fuel Pump Module Control High
What does that mean?
This generic powertrain diagnostic trouble code (DTC) typically applies to all OBD-II vehicles equipped with a fuel pump control module. That may include but is not limited to vehicles from Ford, Chevrolet, Dodge, Chrysler, Audi, VW, Mazda, etc.
In older systems, vehicles required very little fuel pressure . These days on the other hand, with the invention of fuel injection and other systems, our vehicles require higher fuel pressures.
The Engine Control Module (ECM) meets our fuel needs by relying on the Fuel Pump Module to regulate pressures within the fuel system. The fuel pump itself, is responsible for delivering the fuel to the engine.
A failure here is most likely extremely evident as your car may not even start. The 3 main things an internal combustion engine needs to run is : Air, Fuel and Spark. Anyone of these missing and your engine will not operate.
The ECM activates P025D and associated codes when it monitors one or multiples conditions outside a specific electrical range within the Fuel Pump Control Module or it’s circuit. This can be caused by either a mechanical or an electrical problem. Working with/around such a volatile substance makes it somewhat dangerous to diagnose or repair anything here so make sure you are properly trained and are familiar with the hazards involved.
P025D Fuel Pump Module Control High code is set when the ECM monitors a higher than desired specific electrical value within the Fuel Pump Module or it’s circuit(s). It is one of four related codes, which are P025A, P025B, P025C, and P025D.
What is the severity of this DTC?
I would say the severity of this code would be determined by your symptoms. If your car does not start, this would be severe. On the other hand, if your vehicle is operating normally and fuel mileage isn’t being affected and this code is active, this isn’t a very severe situation. That being said, neglecting any fault may result in further time and costs.
An example of a fuel pump control module:
What are some of the symptoms of the code?
Symptoms of a P025D trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P025D troubleshooting steps?
Be sure to check for technical service bulletins (TSBs) for your vehicle. Getting access to a known fix can save you time and money during diagnosis.
Tools
Some of the things you may need when diagnosing or repairing the fuel pump circuits and systems:
Safety Tips
NOTE: ALWAYS verify and record the integrity of your battery and charging system before further troubleshooting.
Basic Step #1
If your car does not start, there is one very easy backyard diagnosing approach. If your vehicle is equipped with a fuel pump mounted inside the fuel tank, you could give the tank a hit with a rubber mallet to potentially dislodge debris out of the pump while someone tries to start the vehicle. If your vehicle fires up when you do this, your diagnosing is complete, you need to replace the fuel pump itself.
NOTE: Whenever diagnosing/repairing anything involving the fuel system, make sure there are no fuel leaks present. Working around fuel with metal tools is an avoidable hazard. Be aware!
Basic Step #2
Take a peek at the connectors and wires. Given the location of most fuel pumps and circuits, they may be difficult to access. You may have to elevate the vehicle somehow (Ramps,jacks,stands,hoist etc..) to gain better access to connectors. Typically, the pump’s harness’ are susceptible to extreme conditions being that most are routed under the vehicle. Make sure the connectors are properly fastened and are not damaged.
NOTE: Sometimes these harness’ are routed along frame rails, rocker panels and other location where wire pinching is common.
Basic Tip #3
Test your pump. Testing the Fuel Pump may not be an easy task. If the fuel pump’s connector is accessible you could use your multimeter to do a series of tests to verify the functionality of the fuel pump itself.
NOTE: Refer to your service manual to know what specific tests can be done here. There is no generic test here so make sure you have the correct information before proceeding.
Basic Step #4
Is there a fuse involved? Maybe a relay? If so, check these. Specifically, a blown fuse could potentially cause an open condition with the circuit (P025A).
Basic Step #5
To verify the integrity of the wires within the circuit, you may be able to disconnect the circuit at both the fuel pump and the ECM. If this is possible, you could perform a series of tests to determine:
1. if there is a fault within the wires and/or
2. what type of fault is present.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p025d and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p025d in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p025d and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p025d.
