P023D Manifold Absolute Pressure – Turbocharger/Supercharger Boost Sensor “A” Correlation
OBD-II Trouble Code Technical Description
Manifold Absolute Pressure – Turbocharger/Supercharger Boost Sensor A Correlation
What does that mean?
This is a generic powertrain diagnostic trouble code (DTC) that typically applies to OBD-II vehicles. That may include but is not limited to vehicles from Land Rover (Range Rover, Discovery), Ford, Chevrolet, Mazda, Dodge, Peugeot, Saab, Toyota, etc.
Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
If your OBD-II equipped vehicle has stored a code P023D, it means that the powertrain control module (PCM) has detected a discrepancy in the correlating signals between the manifold absolute pressure (MAP) sensor and the turbocharger/supercharger boost sensor which has been designated "A".
The "A" denotes a specific boost sensor in a system which may use multiple boost sensors in different locations. Consult a reliable vehicle information source to determine precisely which sensor the A references (for the vehicle in question). This code is applicable only to vehicles that are equipped with forced air induction devices Forced air induction devices include turbochargers and superchargers.
The MAP sensor provides the PCM with a voltage signal that reflects air density or pressure in the intake manifold. The voltage signal is received (by the PCM) as either kilopascal (kPa) units or inches of mercury (Hg). In Some vehicle applications, MAP is substituted for barometric pressure and measured in similar increments.
The turbocharger/supercharger boost pressure sensor (designated A) will likely be of a similar design to the MAP sensor. It monitors air density (boost pressure) inside the turbocharger/supercharger intake pipe and provides the PCM with an appropriate voltage signal.
A code P023D will be stored, and a malfunction indicator lamp (MIL) may be illuminated, if the PCM detects voltage signals between the MAP sensor and the turbocharger/supercharger boost sensor A which differ by more than a programmed degree. Multiple ignition cycles (with a failure) may be required for MIL illumination.
What is the severity of this DTC?
Overall engine performance and fuel efficiency may be adversely affected by the conditions which contribute to a code P023D. It should be categorized as severe.
What are some of the symptoms of the code?
Symptoms of a P023D trouble code may include:
What are some of the common causes of the code?
Causes for this P023D trouble code may include:
What are some P023D troubleshooting steps?
I would first gain access to diagnostic scanner, a digital volt/ohmmeter (DVOM), a manual vacuum pressure gauge, and a reliable vehicle information source before attempting to diagnose a code P023D. Diagnosing any MAP sensor related code should include making sure that the engine is making sufficient vacuum. This may be done using the vacuum pressure gauge.
A visual inspection of all MAP/ turbocharger/supercharger boost sensor system wiring and connectors is in order if there are no intercooler obstructions and the air filter is relatively clean. Make repairs as required. Next, I would connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. Freeze frame data could be best described as a snap shot of the exact circumstances which were occurring at the time of the malfunction which led to the stored code P023D. I like to write this information down as it may be helpful as the diagnosis proceeds. Now, clear the codes and test-drive the vehicle to see if the code is reset.
If it is:
If the sensors all comply with manufacturer’s specifications:
If you find reference voltage and a ground:
If the sensor signal circuit reflects the correct degree of voltage:
Suspect PCM failure or a PCM programing error if all MAP/ turbocharger/supercharger boost pressure sensors and circuits are within specifications.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p023d and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p023d in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p023d and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p023d.
